Designation |
Assistant Professor |
Department |
Mechanical Engineering |
Date of Joining |
12/08/2013 |
Education |
|
Specialization |
Specialization in Production (Manufacturing and Automation) |
Areas of Interest |
Production, Optimization and Maintenance |
mahadev.naik@famt.ac.in |
Institute | Duration | Designation |
FAMT, Ratnagiri | 12/08/2013 to till date | Assistant Professor |
Sandip Institute of Technology & Research Centre, Nashik | 26/06/2012 to 01/01/1970 | Assistant Professor |
SSPM COE | 22/07/2011 to 01/01/1970 | Lecturer |
Government Polytechnic Ratnagiri | 10/09/2008 to 09/03/2009 | Lecturer |
1.
Worked as
Training Head of FAMT of from
01/01/1970 to
01/01/1970.
2.
Worked as
Training Head of FAMT of from
01/06/2017 to
01/01/1970.
1. M. L. Naik and S. D. Rane and Y. . Patil and A. R. Sawant and S. . Solkar, "Analysis of Spring back Variation in V-bending using Taguchi Technique of Al-5251 H24 alloy,"Journal of Emerging Technologies and Innovative Research (JETIR), vol. 6, no.1, pp. 458 - 466, 6-2019
2. M. L. NAIK and K. . Bhosale and M. . Bhide and S. . Bhokare and S. . Bhangale, "DESIGN AND DEVELOPMENT OF WASTE HEAT RECOVERY FOR FILE CLEANING OPERATION BY USING FIN TYPE HEAT EXCHANGER,"International Journal of Creative Research Thoughts (IJCRT, vol. 6, no.2, pp. 1233 - 1246, 4-2018
3. M. L. NAIK and A. . Makandar and S. . Manerikar and P. . Malik and G. . Mane, "OPTIMIZATION OF PROCESS PARAMETERS IN TIG WELDING USING TAGUCHI OF 5086- ALUMINIUM ALLOY,"International Journal of Creative Research Thoughts (IJCRT) , vol. 6, no.2, pp. 600 - 605, 4-2018
4. M. L. NAIK and P. . Kadam and S. . Kadam and D. . Kadam and D. . Kulkarni, "Fault Diagnosis and experimental analysis of 4-stroke, 4-cylinder petrol engine using Fault Tree Analysis ,"International Journal of Engineering Trends and Technology (IJETT) , vol. 46, no.8, pp. 445 - 453, 4-2017
5. M. L. NAIK and A. . Gorule and A. . Ajgaonkar and T. . Dudye and T. . Chavan, "Optimization of turning process parameters for AISI 410 Steel using Taguchi method,"International Journal of Engineering Development and Research , vol. 4, no.2, pp. 591 - 595, 05-2016
1. Attended international conference ICIE 2019 at
SVNIT, Surat
from
12/12/2019 to 14/12/2019
2. Attended international conference ICIE 2017 at
SVNIT, Surat
from
21/12/2017 to 23/12/2017
3. Attended international conference AEOTIT 2013 at
SVNIT, SURAT
from
01/07/2013 to 03/07/2013
1. Attended seminar on Steps to Research held on
19/09/2014 .
2. Attended seminar on Steps to Research held on
19/09/2014 .
1. Attended Workshop on Advances in industrial engineering and management held in December, 2018
.
1. Completed FDP on Introduction to Research held in August, 2019
.
1. Completed STTP on Open source solutions in Teaching-Learning process held in June, 2019
.
2. Completed STTP on Modeling and Optimization Techniques for Engineering Applications held in December, 2016
.
1. Completed NPTEL course on Fundamentals of Manufacturing Processes held in July, 2017
.
1. Parametric Optimization of TIG Welding on ASTM B221 aluminium alloy by Taguchi method. MINOR project is close
funded by
University of Mumbai of Rs. 30000 from duration
2017-08-28 to 2018-03-31
.
2. Parametric optimization of TIG welding on 5086 aluminium alloy. MINOR project is close
funded by
University of Mumbai of Rs. 30000 from duration
2017-07-01 to 2018-03-31
.
1. Production Planning and Control course taught to Mechanical Sem 7
with experience of
05 years
.
2. Industrial Engineering and Management course taught to Mechanical Sem 8
with experience of
04 years
.
3. Press Tool Design course taught to Mechanical Sem 5
with experience of
02 years
.
4. Production Process III course taught to Mechanical Sem 5
with experience of
03 years
.
5. Production Process II course taught to Mechanical Sem 5
with experience of
03 years
.
6. Computer aided Machine Drawing course taught to Mechanical Sem 3
with experience of
01 years
.
7. Industrial Engineering and Management course taught to Mechanical Sem 8
with experience of
04 years
.
8. Production Planning and Control course taught to Mechanical Sem 7
with experience of
05 years
.
9. Press tool design course taught to Mechanical Sem 5
with experience of
02 years
.
10. Production Process III course taught to Mechanical Sem 5
with experience of
03 years
.
11. Production Process II course taught to Mechanical Sem 4
with experience of
03 years
.
1. College to corporate Program- Soft skills MINOR event is organised by
Mechanical Engineering department
from duration
07/09/2017 to 12/09/2017
,participants: 30 .