Designation |
Assistant Professor |
Department |
Mechanical Engineering |
Date of Joining |
10/07/2006 |
Education |
|
Specialization |
Specialization in Machine Design |
Areas of Interest |
Production, Machine Design |
gayatri.abhyankar@famt.ac.in |
Institute | Duration | Designation |
Finolex Academy of Management & Technology | 13/04/2010 to till date | Assistant Professor |
Rajendra Mane College of Engineering and Technology | 04/07/2005 to 08/07/2006 | Lecturer |
Finolex Academy of Management & Technology | 10/07/2006 to 13/04/2010 | Lecturer |
1.
Working as
Internal Complaint Committee of Member of Internal complaint committee from
30/10/2018 to
till date.
2.
Working as
Mahavidyalayin Vidyarthinichi Suraksha Samiti of Faculty member from
28/01/2019 to
till date.
3.
Working as
Attendance Committee of Mechanical Departmental coordinator from
25/07/2018 to
till date.
4.
Working as
Women Grievance cell of Committee Member from
01/07/2016 to
till date.
5.
Worked as
Women Grievance cell of Member of Women Grievance cell from
04/01/2013 to
28/04/2024.
6.
Worked as
Women Development Cell of Teaching staff representative from
12/02/2013 to
28/04/2024.
7.
Worked as
Unfair means enquiry committee of Member from
17/01/2014 to
28/04/2024.
8.
Worked as
Senior Supervisor of Senior Supervisor for morning session from
24/04/2018 to
06/10/2018.
9.
Worked as
Senior Supervisor of Senior Supervisor (Morning session) from
12/03/2014 to
06/10/2014.
10.
Worked as
Senior Supervisor of Senior Supervisor for MCA examination (evening session) from
17/04/2008 to
06/10/2008.
11.
Worked as
Women Development Cell of Teaching staff representative of Women Development Cell from
05/07/2017 to
07/05/2019.
1. G. J. Abhyankar and R. . Manjrekar and K. . Karalkar and A. . Lavande and H. . Kavache, "Experimental Investigation of Abrasive Jet Machining,"ijsart, vol. 5, no.6, pp. 318 - 321, 6-2019
2. G. J. Abhyankar and O. . Mestry and R. . Dharne and P. . Gokhale and V. . Dabholkar, "Casting Design And Simulation of QRL Cylinder For Defect Minimization Using Autocast Software,"ijsart, vol. 5, no.6, pp. 483 - 488, 6-2019
3. R. H. Deshmukh and M. . Dhoke and B. . Kale and G. J. Abhyankar, "Review on Performance Improvement of Centrifugal Pump,"International Journal of Creative Research Thoughts, vol. 6, no.2, pp. 1682 - 1689, 4-2018
4. V. z. Zore and R. . Yadav and M. . Wasta and A. . Vardam and G. J. Abhyankar, "Investigation of Influence and optimization of various process parameters on springback in UHMWPE,"International Journal of Science and Advanced Research in technology, vol. 4, no.4, pp. 3054 - 3060, 4-2018
5. G. J. Abhyankar and V. . Holkar and B. . Malkar and G. . Sutar and R. . Teli, "Design Analysis and Experimental Investigation of composite mono leaf spring,"International Journal of Recent Trends in Engineering and Research, vol. 3, no.5, pp. 350 - 358, 5-2017
1. Attended international conference ICIE 2019 at
SVNIT, Surat
from
12/12/2019 to 14/12/2019 and published paper titled Structural Equation Modelling (SEM) of Success Factors for Medical Device Development
2. Attended international conference ICIE 2017 at
SVNIT, Surat
from
21/12/2017 to 23/12/2017 and published paper titled Medical Product Development Process: An Exploration of Sources of Risks
1. Attended Workshop on Python workshop held in June, 2019
.
2. Attended Workshop on Two days workshop on Intellectual Property Rights held in March, 2019
.
3. Attended Workshop on One week workshop on " Funding Schemes Available for Research Proposal" held in February, 2016
.
4. Attended Workshop on Two day ISTE e seminar on Steps 2 Research held in September, 2014
.
5. Attended Workshop on Two Week ISTE Workshop on Engineering Thermodynamics held in December, 2012
.
6. Attended Workshop on Two days ISTE workshop on Akash for Education held in November, 2012
.
7. Attended Workshop on Two week workshop on Introduction to Research Methodologies held in June, 2012
.
8. Attended Workshop on One Day Workshop "Six Sigma: An overview" held in April, 2012
.
9. Attended Workshop on National Symposium On Novel Ideas in CFD - SONIC 07 held in December, 2007
.
1. Completed FDP on Introduction to Research held in August, 2019
.
2. Completed FDP on Open Source Solutions in Teaching Learning Process held in June, 2019
.
3. Completed FDP on Recent Advances in Computer Aided Engineering held in June, 2018
.
1. Completed STTP on Energy Efficient Practices in Refrigeration and Air Conditioning held in December, 2019
.
2. Completed STTP on STTP on Total Quality Management in Technical Education (TQM) held in June, 2008
.
1. Completed NPTEL course on Introduction to Research held in August, 2019
.
2. Completed NPTEL course on NPTEL - Fundamentals Of Manufacturing Processes held in July, 2017
.
1. Member of
The Indian Society For Technical Education ,no: 56179
from 2008
1. Production Process I course taught to Mechanical Sem 3
with experience of
13 years
.
2. Production Process II course taught to Mechanical Sem 4
with experience of
11 years
.
3. System Modelling and Analysis course taught to FE Sem 2
with experience of
4 years
.
4. Machine Design I course taught to Mechanical Sem 6
with experience of
1 years
.
5. Theory of Machines course taught to Mechanical Sem 5
with experience of
1 years
.
6. Operations Rsearch course taught to Mechanical Sem 7
with experience of
7 years
.